BluePrint Engines GM LS Pro Series 427 Crate Engine Deluxe Dressed 605 HP w/ Holley Terminator X EFI/ Black Pulleys

Get 605 horsepower and 565 ft-lbs. of torque with this crate engine (PSLS4273CTFKB) from BluePrint Engines! It comes deluxe dressed and has a slick black pulley kit. It also includes a Holley Terminator X Max EFI for real time fuel map learning.

Features and Benefits:
- High-strength cast iron LSX-style base-dressed crate engine block
- 605 Horsepower / 565 FT. LBS. Torque
- Compression Ratio: 11:1
- Features 6-bolt main, 4.0685" bore, and 1-piece rear main seal
- Priority main oiling and improved water jacket design
- Increased deck thickness and strength webbing with extended cylinder skirt
- Forged crankshaft and pistons with 4.125" rotation stroke
- Forged 6.125" connecting rods
- Internally balanced at the front and rear
- Hydraulic roller cam design
- Utilizes OEM LS3 front and rear covers
- Backed by BluePrint Engines' 30-month/50,000-mile warranty

Cylinder Head Specifications:
- 69cc Chambers
- 2.165" Intake / 1.590" Exhaust Valves
- 259cc Intake / 102cc Exhaust Runners

Camshaft Specifications:
- 0.624" Intake / 0.624" Exhaust Lift
- 239 Intake / 255 Exhaust Duration
- @ 0.050-114 degrees Lobe Separation

Holley Terminator X Max Features and Benefits:
- Real time fuel map learning simplifies tuning by dynamically adjusting the base fuel rate
- On board Bosch LSU 4.9 wideband control, enabling accurate AFR readings and closed loop tuning
- Eight high impedance injector drivers, ideal for stock LS injectors and Holley EFI injectors
- Integrated 1-Bar MAP sensor for naturally aspirated or nitrous setups, with harness support for external higher bar sensors if needed
- 4 configurable inputs (12V, Ground, 5V, Frequency) and 2 outputs (Ground, PWM) ideal for electric fans, boost control solenoids, nitrous control and more
- Free PC tuning software via USB/CAN interface for full laptop control and advance setup
- Integrated 3.5" touchscreen handheld with setup Wizard, internal data logging, and real time gauge displays
- Terminator X Max ECU will include a base timing map pre-configured for this engine

Deluxe Dressed Includes:
- LS Swap Oil Pan - windage tray - pickup screen
- Fuel Injectors and Rail
- DBW Throttle Body
- Throttle Pedal and Sensors
- GM Plastic Intake Manifold
- Spark Plugs and Wires
- Harmonic Balancer
- Coil Packs
- Polished Pulley Kit (LS2 Water Pump, 1-Wire 140-amp Alternator, Peanut-style A/C compressor, Type II Power Steering Pump w/remote reservoir)

Additional Notes:
- This Holley EFI Equipped engine has a fully calibrated ECU by BluePrint Engines. Please DO NOT follow the Holley EFI manual for the calibration of the ECU.
- Holley terminator X MAX System supports transmission control, but requires additional Transmission harness such as BPP558405
- This engine requires a non-weighted flex plate/flywheel.
- The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low-profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
- Retro fit oil pan will fit most 1955-1995 GM front engine, RWD, V8 cars
- Not for use in pollution-controlled vehicles or in dry sump applications.
- BluePrint Engines Recommends Air Intake Kit BPPLS01013 to ensure correct MAF calculations and Dyno calibration are maintained with the provided ECU / tuning.