AMK Products Underhood Detailing Kit 147-Piece Chevelle 66

Put the finishing touches on your 1966 Chevelle's engine bay with this AMK Products underhood detailing kit. Containing 147 pieces of original-style, factory-correct hardware, this comprehensive kit replaces incorrect, worn, missing, or unsightly fasteners throughout the underhood area for a more authentic finished appearance.

Features and Benefits:
- Comprehensive 147-piece underhood detailing kit
- Original-style, factory-correct replacement hardware
- Replaces incorrect, missing, worn, or unsightly fasteners
- Covers numerous components throughout the engine bay
- Individually packaged hardware sets
- Detailed package labeling helps identify proper placement
- Includes application-specific quantities
- Simplifies sourcing underhood restoration hardware
- Helps restore an authentic underhood appearance
- Ideal for complete restorations and finishing details
- Made in the USA

Rather than sourcing numerous individual fastener sets, AMK Products combines the necessary hardware for a wide range of underhood components into one convenient package. Hardware is provided for applications including the fenders, grille, hood and hinges, heater components, voltage regulator, wiring, windshield washer bottle bracket, wiper motor, and more.

Each hardware set is individually packaged and thoroughly labeled to identify its intended location and required quantity, helping simplify installation during a restoration. Made in the USA, this 147-piece kit is an excellent finishing detail for an assembled 1966 Chevelle or a complete underhood restoration.

Kit Includes:
- Battery Cable Routing Clip to Frame: Hex washer thread-cutting screw, tooth washers (2 pieces)
- Battery Holdown Clamp: Hex conical SEMS (1 piece)
- Control Arm Cross Shaft (Upper): Retainers, hex bolts "SSC", and washers (12 pieces)
- Fenders to Firewall: Large hex conical SEMS (4 pieces)
- Fenders to Radiator Support: Hex pilot-point conical SEMS (4pieces)
- Fender Tie Bar: Hex pilot-point conical SEMS and tubular rivets (8 pieces)
- Grille: Tubular rivets (17 pieces)
- Headlight, Parking Light Grounds, Junction Block: hex washer tapping and sheet metal screws and tooth washers (5 pieces)
- Heater Box and Blower Housing to Firewall: Hex tapping flat SEMS, stamped nuts, and sealer (12 pieces)
- Heater Hose Clip at Wheelhouse: Foldover metal clip (1 piece)
- Hood & Hinges: Hex conical sems (8 pieces)
- Hood Catch & Lock Plate: Hex pilot-point conical sems (9 pieces)
- Hood Levelers (Front): Screws, flange nuts, rubber bumpers (6 pieces)
- Horn: Hex pilot-point conical tooth SEMS (1 piece)
- Horn Relay: Hex washer tapping screw (1 piece)
- Radiator & Center Shroud (Small Block only 65, 67): Hex pilot-point conical SEMS and U-nuts (12 pieces)
- Radio Ground Straps to Firewall: hex washer tapping screws and tooth washers (4 pieces)
- Voltage Regulator: Serrated hex washer machine screws and well-nuts (6 pieces)
- Wheelhouses to Fenders: Hex pilot-point conical SEMS, cup washers, U-nuts (12 pieces)
- Windshield Washer Bottle Bracket: Hex washer tapping screws (3 pieces)
- Windshield Wiper Hoses: 3" nylon straps (2 pieces)
- Wiper Motor (Square Style): Grommets, 1.71" overall-length strap, rivet, and screws (8 pieces)
- Wiring – Blower Motor/Starter Wiring: Rubber coated J-clips (2 pieces)
- Wiring – Brake Warning Switch to Line: 3.17" nylon strap (1 piece)
- Wiring – Voltage Regulator Ground: Hex washer tapping screws and tooth washer (3 pieces)
- Wiring Gutter to Firewall: hex washer tapping screws (2 pieces)
- Wiring Harness to Radiator Support: 3" nylon strap (1 piece)

Vehicle Fitment:
- 1966 Chevelle