AMK Products Underhood Detailing Kit 162-Piece Chevelle 67

Put the finishing touches on your 1967 Chevelle's engine bay with this AMK Products underhood detailing kit. Containing 162 pieces of original-style, factory-correct hardware, this comprehensive kit replaces incorrect, worn, missing, or unsightly fasteners throughout the underhood area for a more authentic finished appearance.

Features and Benefits:
- Comprehensive 162-piece underhood detailing kit
- Original-style, factory-correct replacement hardware
- Replaces incorrect, missing, worn, or unsightly fasteners
- Covers numerous components throughout the engine bay
- Individually packaged hardware sets
- Detailed package labeling helps identify proper placement
- Includes application-specific quantities
- Simplifies sourcing underhood restoration hardware
- Helps restore an authentic underhood appearance
- Ideal for complete restorations and finishing details
- Made in the USA

Rather than sourcing numerous individual fastener sets, AMK Products combines the necessary hardware for a wide range of underhood components into one convenient package. Hardware is provided for applications including the fenders, grille, hood and hinges, brake booster, master cylinder, heater components, horns, voltage regulator, windshield washer components, wiring, wiper motor, and more.

Each hardware set is individually packaged and thoroughly labeled to identify its intended location and required quantity, helping simplify installation during a restoration. Made in the USA, this 162-piece kit provides a convenient way to complete an assembled 1967 Chevelle or add the finishing details to a comprehensive underhood restoration.

Kit Includes:
- Accelerator Lever & Support: Hex bolt, hex washer tapping screws, washers, and nut (6 pieces)
- Battery Cable Routing Clip to Frame: Hex washer thread-cutting screw and tooth washers (2 pieces)
- Battery Hold-Down Clamp: Hex conical SEMS (1 piece)
- Brake Booster: Hex nuts and split washers (8 pieces)
- Control Arm Cross Shaft (Upper): Retainers, "SSC" hex bolts, and washers (12 pieces)
- Fenders to Firewall: Large hex conical SEMS (4 pieces)
- Fenders to Radiator Support: Hex pilot-point conical SEMS and hex washer pilot-point screws (4 pieces)
- Fender Tie Bar: Hex washer pilot-point screws and rivets (4 pieces)
- Grille: Rivets, screw, and nut (16 pieces)
- Headlight, Parking Light Grounds & Junction Block: Hex washer tapping and sheet metal screws and tooth washers (5 pieces)
- Heater Box & Blower Housing to Firewall: Hex internal/external SEMS, stamped nuts, sealer, and seal (13 pieces)
- Heater Hose Clip at Wheelhouse: Fold-over metal clip (1 piece)
- Hood & Hinges: Hex conical SEMS (8 pieces)
- Hood Catch & Lock Plate: Hex pilot-point conical SEMS (9 pieces)
- Hood Levelers (Front): Screws, flange nuts, and rubber bumpers (6 pieces)
- Horn Relay: Hex washer tapping screw (1 piece)
- Horns: Hex pilot-point conical tooth SEMS (2 pieces)
- Master Cylinder: Hex nuts and split washers (4 pieces)
- Radiator & Center Shroud: Hex pilot-point conical SEMS and U-nuts (12 pieces)
- Radio Ground Straps to Firewall: Hex washer tapping screws (2 pieces)
- Voltage Regulator: Serrated hex washer machine screws and well-nuts (6 pieces)
- Wheelhouses to Fenders: Hex pilot-point conical SEMS, cup washers, and U-nuts (12 pieces)
- Windshield Washer Bottle Bracket: Hex washer tapping screws and rubber caps (6 pieces)
- Windshield Washer Nozzles: #8 hex washer sheet metal screws (2 pieces)
- Windshield Wiper Hoses: 3" nylon straps (3 pieces)
- Wiper Motor (Square Style): Grommets, 1.71" overall-length strap, rivet, and screws (8 pieces)
- Wiring – Blower Motor/Starter Wiring: Rubber-coated J-clips (2 pieces)
- Wiring – Brake Warning Switch to Line: 3.17" nylon strap (1 piece)
- Wiring Gutter to Firewall: Hex tapping flat SEMS (2 pieces)

Vehicle Fitment:
- 1967 Chevelle