AMK Products Underhood Detailing Kit 136-Piece Chevelle 68

Put the finishing touches on your 1968 Chevelle's engine bay with this AMK Products underhood detailing kit. Containing 136 pieces of original-style, factory-correct hardware, this comprehensive kit replaces incorrect, worn, missing, or unsightly fasteners throughout the underhood area for a more authentic finished appearance.

Features and Benefits:
- Comprehensive 136-piece underhood detailing kit
- Original-style, factory-correct replacement hardware
- Replaces incorrect, missing, worn, or unsightly fasteners
- Covers numerous components throughout the engine bay
- Individually packaged hardware sets
- Detailed package labeling helps identify proper placement
- Includes application-specific quantities
- Simplifies sourcing underhood restoration hardware
- Helps restore an authentic underhood appearance
- Ideal for complete restorations and finishing details
- Made in the USA

Rather than sourcing numerous individual fastener sets, AMK Products combines the necessary hardware for a wide range of underhood components into one convenient package. Hardware is provided for applications including the fenders, hood and hinges, brake booster, master cylinder, grille brackets, radiator, fan shroud, heater components, voltage regulator, windshield washer components, wiring, wiper motor, and more.

Each hardware set is individually packaged and thoroughly labeled to identify its intended location and required quantity, helping simplify installation during a restoration. Made in the USA, this 136-piece kit provides a convenient way to complete an assembled 1968 Chevelle or add the finishing details to a comprehensive underhood restoration.

Kit Includes:
- Accelerator Lever Support: Hex washer AB screws (2 pieces)
- Battery Cable Routing Clip to Firewall: Hex washer T1 screw (1 piece)
- Battery Hold-Down Clamp: Hex conical SEMS (1 piece)
- Brake Booster: Hex nuts and split washers (8 pieces)
- Control Arm Cross Shaft (Upper): Retainers, "SSC" hex bolts, and washers (12 pieces)
- Fenders to Firewall: Large hex conical SEMS (4 pieces)
- Fenders to Radiator Support: Hex washer pilot-point screws (4 pieces)
- Grille Brackets: Hex washer pilot-point screws (3 pieces)
- Headlight, Parking Light Grounds & Junction Block: Hex washer AB and B screws and tooth washers (5 pieces)
- Heater Box & Blower Housing to Firewall: Hex internal/external SEMS, stamped nuts, sealer, and seal (13 pieces)
- Heater Hose Clip at Wheelhouse: Fold-over metal clip (1 piece)
- Hood & Hinges: Hex conical SEMS (8 pieces)
- Hood Catch & Lock Plate: Hex washer pilot-point screws and hex pilot-point conical SEMS (9 pieces)
- Hood Levelers (Front): Screws, flange nuts, and rubber bumpers (6 pieces)
- Horn: Hex pilot-point conical tooth SEMS (1 piece)
- Horn Relay: Hex washer AB screw (1 piece)
- Master Cylinder: Hex nuts and split washers (4 pieces)
- Radiator – 307/327/350: Hex washer pilot-point screws (3 pieces)
- Radiator Fan Shroud – Small Block: Hex pilot-point conical SEMS, U-nuts, and S-clips (6 pieces)
- Radio Ground Straps to Firewall: Hex washer AB screws (2 pieces)
- Radio Hood Ground Clip to Cowl: Hex AB flat SEMS (1 piece)
- Voltage Regulator: Hex washer AB screws (3 pieces)
- Wheelhouses to Fenders: Hex washer pilot-point screws, cup washers, and U-nuts (12 pieces)
- Windshield Washer Bottle Bracket: Hex washer AB screws (3 pieces)
- Windshield Washer Nozzles: #8 hex washer B screws (2 pieces)
- Wiper Motor (Round Style): Grommets, 3.25" overall-length strap, and screws (10 pieces)
- Wiring – Blower Motor/Starter Wiring: Rubber-coated J-clips (2 pieces)
- Wiring – Engine Near Wiper Motor: Rubber-coated J-clip and hex washer screw (2 pieces)
- Wiring – Horn: S-clips (3 pieces)
- Wiring Gutter to Firewall: Hex AB flat SEMS (2 pieces)
- Wiring Harness to Driver Side Wheelhouse: Push-end black plastic straps (2 pieces)

Vehicle Fitment:
- 1968 Chevelle