AMK Products Underhood Detailing Kit 128-Piece Chevelle 71

Put the finishing touches on your 1971 Chevelle's engine bay with this AMK Products underhood detailing kit. Containing 128 pieces of original-style, factory-correct hardware, this comprehensive kit replaces incorrect, worn, missing, or unsightly fasteners throughout the underhood area for a more authentic finished appearance.

Features and Benefits:
- Comprehensive 128-piece underhood detailing kit
- Original-style, factory-correct replacement hardware
- Replaces incorrect, missing, worn, or unsightly fasteners
- Covers numerous components throughout the engine bay
- Individually packaged hardware sets
- Detailed package labeling helps identify proper placement
- Includes application-specific quantities
- Simplifies sourcing underhood restoration hardware
- Helps restore an authentic underhood appearance
- Ideal for complete restorations and finishing details
- Made in the USA

Rather than sourcing numerous individual fastener sets, AMK Products combines the necessary hardware for a wide range of underhood components into one convenient package. Hardware is provided for applications including the fenders and extensions, hood and hinges, brake booster, master cylinder, grille brackets, radiator, fan shroud, fuel vapor canister, heater components, voltage regulator, windshield washer components, wiring, wiper motor, and more.

Each hardware set is individually packaged and thoroughly labeled to identify its intended location and required quantity, helping simplify installation during a restoration. Made in the USA, this 128-piece kit provides a convenient solution for completing an assembled 1971 Chevelle or adding the finishing details to a comprehensive underhood restoration.

Kit Includes:
- Accelerator Lever Support: Hex washer AB screws (2 pieces)
- Battery Hold-Down Clamp: Hex conical SEMS (1 piece)
- Brake Booster: Flange nuts (4 pieces)
- Control Arm Cross Shaft (Upper): Retainers, "SSC" hex bolts, and washers (12 pieces)
- Fender Extensions – Top Brackets: Hex conical AB SEMS and spring nuts (4 pieces)
- Fenders to Firewall: Hex CA conical SEMS (4 pieces)
- Fenders to Radiator Support: Hex washer CA screws (4 pieces)
- Fuel Vapor Canister: Hex washer AB and CA screws (3 pieces)
- Grille Brackets: Hex washer CA screws (7 pieces)
- Headlight, Parking Light Grounds & Junction Block: Hex washer AB screws, nuts, and tooth washer (4 pieces)
- Heater Box & Blower Housing to Firewall: Hex internal/external SEMS, stamped nuts, sealer, and seal (13 pieces)
- Heater Hose Clip at Wheelhouse: Fold-over metal clip (1 piece)
- Heater Hose Clip to Alternator Bracket without A/C: Fold-over metal clip (1 piece)
- Hood & Hinges: Hex conical SEMS (8 pieces)
- Hood Catch & Lock Plate: 12-point conical SEMS (8 pieces)
- Hood Levelers (Front): Screws, flange nuts, and rubber bumpers (6 pieces)
- Hood Levelers (Rear): Jam nuts (2 pieces)
- Horn (Low Note) to Hood Catch Support: Hex pilot-point conical SEMS (1 piece)
- Horn Relay: Hex washer AB screw (1 piece)
- Master Cylinder: Flange nuts (2 pieces)
- Radiator – 307/327/350: Hex washer CA screws (3 pieces)
- Radiator Fan Shroud: Hex flat SEMS, S-clips, and spring nuts (6 pieces)
- Voltage Regulator: Hex washer AB screws (3 pieces)
- Wheelhouses to Fenders: Hex pilot-point conical SEMS and flat washers (8 pieces)
- Windshield Washer Bottle: Hex washer AB screws (2 pieces)
- Windshield Washer Nozzles: #10 hex washer AB screws (2 pieces)
- Wiper Motor (Round Style): Grommets, 3.25" overall-length strap, and screws (10 pieces)
- Wiring – Alternator to Heater Hose: 7.1" flexible strap (1 piece)
- Wiring – Blower Motor/Starter Wiring: Rubber-coated J-clips (2 pieces)
- Wiring – Engine Near Wiper Motor: Rubber-coated J-clip and hex washer screw (2 pieces)
- Wiring Gutter to Firewall: Hex AB flat SEMS (2 pieces)
- Wiring Harness to Driver Side Wheelhouse: Push-end black plastic straps (2 pieces)

Vehicle Fitment:
- 1971 Chevelle